Economical and superior quality roof rail designed specifically for the models in Commercial group.
With its superior aerodynamic structure fits completely on the roof of the car and can be installed in very short time and easily.
- Loading Capacity: 75 kg.
- Package Dimensions: 9*10* Product Length cm.
- Installation: Screwing
- Raw Materilas: Extruded aluminum, rubber, copolymer PVC
- Color Alternatives: Black / Polished
- Target Vehicle Group: Commercial Group, Vans-Minivans
- Manufactured painted to black color with electrostatic method ,PVC product heads and gasket system.
- Avanos roof rail is designed for Vans and Minivan group of vehicles.
- Easy and fast installation with screwing system thanks to special gasket system well matched with the roof slope of the car.
- Cross bars could be installed on the products through the original channels on the main pipe
- The product is installed with screwing on the car from the original holes exist on the roof.
I.Disclaimer for Voyager Products
Voyager products are designed to be sold as decorative accessories, and should not be relied upon
as protection for both passengers and vehicle. The buyer assumes all risk and liability whatsoever resulting from the use of said products. There are limitations to the severity of impact that the products sold herein can withstand and the products are not a substitute for safe and careful driving.
II.Care & Cleaning
Although products are made with high quality raw materials which are designed to provide maximum weathering protections, they may be affected negatively by environmental conditions. By following regular care and maintenance it will ensure maximum level of protection and good external appearance. Weekly periodic cleaning is recommended depending on the weather and environmental conditions.
Care and Cleaning Guidelines
- Rinse the product in order to remove the dirt and dusts stuck on the surface with warm water.
- Use a soft, dampened sponge or cloth to clean. Never use abrasive material like a bristle brush or scouring pad.
- The preferred cleaner is one that does not contain chlorine, such as acetone, methyl alcohol, and mineral spirits. Use neutral cleaner cleaners compounded from phosphates, alkalis such as liquid soaps and mild detergent. Do not allow cleaners to sit or soak on the product. Always test your cleaning solution on an inconspicuous area on the product before applying it to the entire surface. These can be used with warm water, bristle brushes, sponges, or clean cloths.
- Rinse the surface completely with water immediately after applying cleaners and than dry it by wiping with soft cloths to prevent streaking. Special care should be taken to remove any traces of cleaner from edges and joins.
- For aluminum surfaces synthetic soft cleaning materials sigh as liquid soap are recommended. Avoid allowing aluminum to scrape against hard or sharp surfaces. Aggressive alkaline or acid cleaners must never be used on anodized aluminum surfaces.
- Never use petrolium based cleaning materials (benzine, gasoline, thinner, etc.. ) on PVC surfaces.
- Be cautious about using chemical solvents, caustic or abrasive cleaners (scouring powders, steel wool, abrasive polishes, etc.) as they may permanently scratch aluminum; painted or anodized aluminum surfaces will be permanently damaged. Test solvent first if the aluminum is painted to be sure it doesn't also remove the paint
- Do not use a metal scraper or abrasive pad. Excessive abrasive rubbing should not be used since it could damage the surface.
- Cleaning hot, sun-heated surfaces should be avoided since possible chemical reactions will be highly accelerated and cleaning non-uniformity could occur.
III.Transportation & Handling
- The products should be delivered with their original packaging.Although the packages are prepared with high resistant raw materials handling and transportation of the products should be made in carefull. They should not be thrown quickly, bump to each other.
- The products should be submitted after the package has been opened and checked. If there is any bend, scracth or any of damage on the product damage report should be prepared with the responsible person from the trasporter company and than they should be submitted.
- The damages during handling or transportation are not covered.
Installation should be made according to installation manual.
- The position of the gasket is written on the gasket check and use the right gasket under the right product head.
- The screwing should be made from the original holes exist on the roof.
- If the connection is made from 3 or 4 holes on the car, the screwing should be made first from the mid points , front and rear screwing should be final.
- Before tighten the screws check and set the product to the right position.